The Z-Wave In-Wall Double Switch Controller is a wireless controller which can be a part of many whole-home automation solutions.
Control the ON-OFF function of two independent circuits remotely or using a momentary / bell type switch
Compatible with all Z-Wave networks
Acts as a repeater expanding your Z-Wave network
Wide range of compatibility with existing light fittings and does NOT require expensive cabling
Product Details
The Z-Wave In-Wall Double Switch Controller is an advanced Z-Wave controller perfect for remotely operating your existing light fittings. It works with Z-Wave enabled controllers (AUS/NZ version) and can be controlled individually or as part of a group in a pre-configured Scene.
The Z-Wave In-Wall Double Switch Controller is designed to operate inside your wall socket and can be easily installed by a qualified electrician.
The controller is also compatible with many popular BELL PRESS type light fittings including Clipsal IMPRESS and SATURN wall switches.
Example of wiring with Clipsal Saturn range 2 gang wall plate and two 30/60PBBPL Bell Press buttons. Clipsal Saturn range 2 gang wall plate and two 30/60PBBPL Bell Press buttons are sold seperately.
This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
Vera 3/Lite
Raspberry PI with RaZberry Card
Fibaro Home Controller 2/Lite
REMOTEC Z-Wave Advanced Remote Controller
Please Note:
Please check the maximum load before installing or operating. This installation must be done by a certified electrician in Australia and New Zealand. Before engaging an electrician, check that they provide an electrical compliance certificate. For warranty claim you have to provide installation compliance certificate from your electrician.
The Vision Z-Wave Range Extender is a smart, discrete Z-Wave device designed to amplify the signals of any Z-Wave devices in your Z-Wave network which helps to eliminate "RF dead spots".
Amplifies signals to a range of up to 100m
Power level control
Wall mountable
micro USB powered
Product Details
The Vision Z-Wave Range extender is designed to amplify the signals of any Z-Wave device in your Z-Wave network. It is compatible with all Z-Wave enabled devices regardless of their manufacturers. This device takes existing Z-Wave signals emitted from nearby devices and sends them to distant Z-Wave devices in your Z-Wave network which would otherwise be unreachable.
This device also allows you to adjust its power level, by reducing its power level you can reduce its power consumption and operational range.
Please Note: The Vision Z-Wave Range Extender is powered by standard micro USB power supply. Neither the micro USB power supply nor the USB cable are included with this product.
The VISION Z-Wave Shock Sensor is a smart, battery-powered sensor which detects any shocks and vibrations on the door or window which it is attached to.
Easy to use and install
Completely wireless
Adjustable sensitivity
Hidden tamper prevention trigger
Low battery alarm notification
Supports one Z-Wave group and up to 5 devices
Product Details
The VISION Z-Wave Shock Sensor is a smart, battery-powered shock and vibration sensor. This device is capable of sending Z-Wave commands to any associated Z-Wave devices within its Z-Wave network when it detects an excessive shock or vibration on a door/window.
This sensor includes a manual calibration and adjustment element to adapt its sensitivity to different applications.
The VISION Z-Wave Shock Sensor also features a hidden tamper prevention switch which will notify an associated Z-Wave gateway if it is tampered with as well as low battery notifications.
This device can easily be fitted to any door, window or other item using screws or double sided tape (included).
Integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
Vera 3
Vera Lite
Fibaro Home Center 2
Technical Specifications
RF Protocol
Z‐Wave (Mulitlevel Command Class)
RF Frequency
921.42Mhz ‐ AU/NZ approved RF for Z‐wave
Z‐Wave device type
Z-Wave multiple level, routing slave
Operating Voltage
2 AA batteries
Status Indicator
LED Light
Operation Range
Up to 30m without obstacles
Application
Indoor
Operation temperature
-10 ~ 50 °C
Storage temperature
‐10 ~ 70 °C, humidity 5 ~ 95% RH (max)
Weight
110g
Housing
ABS
Dimensions
(HxWxD) 75 mm x 42mm x 26mm
Compliance
Certified for USA, EU and AU/NZ markets (FCC, CE, ROHS, C-TICK)
UZB1 is a wireless Z-Wave transceiver which connects a PC, MAC or Linux computing platform to a wireless Z-Wave network via USB port.
Compatible with Windows, Linux and Mac OS systems
Supports and powered by USB 2.0/3.0
Firmware upgrade functionality
Support all Z-Wave certified devices in AUS/NZ/BR frequency of 921.42MHz
Z-Wave Plus certified
Design and made in Germany
Product Details
Smart Home Controller software is required to use UZB1 and can be purchased from various manufacturers around the world. This software must be compatible with Sigma Designs Serial API and have proper Sigma certification to manage and use Z-Wave devices from various manufacturers. This transceiver works with all certified Z-Wave devices with the same RF 921.42 MHz regardless of the manufacturer or date of origin.
Compared to the standard firmware design used by almost all Z-Wave USB Sticks and other Z-Wave Host Interface hardware, the UZB firmware offers several extensions and enhancements:
Backup and recovery function including network topology
Optimized transmitting queue handling to speed up transmitting process
Handling to extend battery life time of battery operated devices in the network
The device implements a virtual serial interface used by the Z-Wave application. Linux and Mac OSX has a built in device driver for the stick and will create a new device named like /dev/cu.usbmodemfa131 (OSX) or /dev/ttyACM0 (Linux). Windows enumerates a new COM device but may require a device driver uzb.inf available below.
If you want to run Z-Way Z-Wave Plus certified software with your ZME UZB1 transceiver to achieve the full Z-Wave gateway, please purchase the Z-Way licence key here at ZwaveEurope.com online shop and follow the procedure to install the licence on your ZME UZB1 transceiver.
The REMOTEC Z-Wave Thermostat ZTS-500 is a programmable electronic thermostat controller allowing you to keep your home at a comfortable temperature at all times. A smart thermostat designed with the end user in mind. It combines compatibility with any Z-Wave certified controller or gateway with an incredibly simple and intuitive user interface.
Support 2 stage heat, 2 stage cool, 2 stage fan
24Vac single & two stage conventional heating systems (gas/oil/electric)
Heat pump systems with up to two stages of heating (electric/gas)
Zoned forced air and zoned hot water (2 or 3 wire)
Millivolt systems (12-24Vac or DC source)
Can be controlled by android smartphones and iPhones (via home controller)
One or two stage cooling systems
Hybrid systems
Z-Wave Dual mode (FLiRS, Always Listening)
Product Details
The REMOTECZ-Wave Thermostat ZTS-500 is an intelligent, programmable thermostat controller with a blue display which is easy to read even in dimly lit areas.
This thermostat delivers permanent day and time settings that are even maintained during power outages. It offers the option to remotely control / check your room temperature via a smart phone or PC which is associated with yourZ-Wave Home controller.
For added convenience, the thermostat unit can be run using battery power or using power from your heating/cooling system, giving you the option of permanently eliminating battery changes.
This thermostat is compatible with a broad range of 24-volt heating and cooling systems, including both single-stage (cooling) and single and two-stage heating systems (non-heat pump), single-stage heat pumps, and heating-only or cooling-only systems. Uses standard thermostat connections:
To check compatibility with your heater or HVAC system please see what terminals are in use at your current heater or HVAC systems.
Function
Terminal
Cool changeover (heat pump)
O
Heat changeover (heat pump)
B
2nd Stage heater
W2
1st Stage heater
W1
Fan
G
Compressor
Y
24Vac Power for Cooling
RC
24Vac Power for Heating
RH
24Vac Common
C
This product integrates with all Australian certified (921.42MHz) Z-Wave controllers including:
Vera Plus/Edge/3/Lite
Fibaro HC2/Lite
Please Note:
This device is not compatible with electric baseboard heaters (120 to 240 volts). It is also not compatible with some multifunction 2-wired Japanese brand heaters and HVAC systems.
If you are not feeling confident with installing this thermostat get a heater/ac installer to do this job for you.
This thermostat is backed by a one year limited warranty.
The Z-Wave A/C Controller (manufactured by Remotec) is a Z-Wave to air-conditioner IR extender.
Control your air-conditioner remotely using a Z-Wave Home Controller
Works with all types of AC IR interface
Built in temperature sensor informs you of current room temperature
USB powered, 5V DC Jack or 1 year battery life on 3 x AAA batteries
Product Details
The Z-Wave A/C Controller is a smart Z-Wave controller which allows you to remotely control your air-conditioner using a compatible Z-Wave controller. It works with any Z-Wave compliant gateway or controller by translating Z-Wave Thermostat Commands to AC IR control code. User can select the IR code from the built‐in code library by using Z-Wave Configuration Commands according to the parameter table, or use the learning function through the gateway. The Z-Wave A/C Controller also has a built‐in temperature sensor which allows your gateway or controller to get the current room temperature.
Product Details
The Z-Wave A/C Controller is a smart Z-Wave controller which allows you to remotely control your air-conditioner using a compatible Z-Wave controller. It works with any Z-Wave compliant gateway or controller by translating Z-Wave Thermostat Commands to AC IR control code. User can select the IR code from the built‐in code library by using Z-Wave Configuration Commands according to the parameter table, or use the learning function through the gateway. The Z-Wave A/C Controller also has a built‐in temperature sensor which allows your gateway or controller to get the current room temperature.
The Z-Wave A/C Controller can be configured as either a “Frequently Listening Routing Slaves” (FLiRS) or an “Always Listening” node before including it to your Vera gateway. The FLiRS node type is for battery operated applications and it will enter sleep mode frequently in order to conserve battery power. The Always Listening node type is for areas where a fast response is required. It works with a 5V DC power source. Always Listening node can act as a repeater, which will re‐transmit the RF signal from the other Z-Wave devices in your network to ensure that the signal reaches its intended destination by routing the signal around obstacles and radio dead spots.
The Z-Wave A/C Controller also supports Network Wide Inclusion (NWI) and Explore Frames. It is compatible with Z‐Wave networks that contain multiple gateways and controllers. Like every Z‐Wave accessory, the user will need to include the Z-Wave A/C Controller into their Z‐Wave network using their primary controller. Then, the user can use either the primary or secondary controller to configure and setup the Z-Wave A/C Controller using Z‐Wave’s configuration command class. Once the configuration and setup is complete, the user can use the Z‐Wave “Thermostat commands class” to control their IR‐controlled air‐conditioner through the Z-Wave A/C Controller.
This product integrates with the follwoing Australian certified (921.42MHz) Z-Wave controllers including:
When one of the buttons on the ZRC-90 is pushed, your Z-Wave central controller will receive a signal which it can use to trigger unlimited control possibilities. With 8 buttons, each supporting a long-press capability, you can control 16 different actions in your central controller. The ZRC-90 is a great solution for triggering events more quickly than taking out your smart-phone and running a home control app. The scene master is ideal for kids, elderlies and guests who may not have full access your to your smart home's mobile application. With a convenient snap-in wall mount, the ZRC-09 can also be removed to keep it handy while you go about your home for the ultimate in simple convenience.
Benefits
Works with any Z-Wave compliant gateway for easy scene activation
Mount anywhere you like, or just put it on your coffee table
Easy access when your phone is not available
Specifications:
Z-Wave Plus compliant
SDK version: 6.51.03
8 buttons can be single or double clicked to trigger 16 different actions from gateway
Control your Z-Wave Gateway with the wall-mount Mini Keypad RFiD. The keypad's "Home" and "Away" buttons allow you to quickly arm/disarm your security system and/or run automation scenarios. Four numbered buttons also provide scene controls. In addition to using pushbutton controls, you can wave the included keychain RFiD Key Tag in front of the keypad to arm/disarm the system.
Supported Z-Wave Gateways:
Vera Lite (UI7)
Vera 3 (UI7)
Product Details
Communicates via Z-Wave to arm/disarm a security system.
The DHS Z-Wave Mini Remote controller allows the user to wirelessly control home appliances using Z-Wave enabled devices.
Highly intuitive and easy to use user interface
Black/white colour enclosures
Can hold up to 4 scenes
Full range of Z-Wave controller functions
Internal lithium battery rechargeable via USB
Product Details
The DHS Z-Wave Mini Remote is a fully functional Z-Wave remote controller capable of adding, removing and controlling other Z-Wave devices. Advanced function include automatic rediscovery of the Z-Wave network as well the ability to become a secondary or inclusion controller to a SIS gateway in the Z-Wave network.
This product allows the user to control home appliances wirelessly using Z-Wave enabled (AUS/NZ version 921.42 MHz) devices like: switches, dimmers, blind controllers, fans, power boards, locks, ect. An internal lithium battery allows for months of usage and can be recharged via USB.
The mini remote offers four control buttons for scene selection. Behind a slider there are four more buttons for Z-Wave network control.
The DHS Z-Wave Advanced Remote (manufactured by Remotec) is capable of creating and controlling a Z-Wave network as well as acting as a secondary controller to an IP Gateway (like Vera 3/Lite).
Control devices individually or in groups using preset scenes(up to 12 scenes)
1 year battery life
Compatible with most Z-Wave enabled devices
Supports multi-channel devices
Product Details
The DHSZ-Wave Advanced Remote is a smart Z-Wave controller designed to operate as either a primary controller, capable of creating and managing its own Z-Wave network, or a secondary controller to an IP Gateway (like Vera 3/Lite).
The DHS Z-Wave Advanced Remote works with almost all Z-Wave enabled devices including; binary switches, dimmers, thermostats, door locks, binary or multi-level sensors. Users can control their Z-Wave enabled devices individually or through “Scene” control. A scene is a collection of Z-Wave devices configured to user-preferred settings, levels, modes or operating conditions which can all be activated with a single command.
The DHS Z-Wave Advanced Remote is also equipped with a backlit LCD screen and an intelligent Self Navigated Button (SNB) system. Users can setup and operate their Z-Wave devices using this remote, and enjoy a networked, wireless home automation system anywhere at home.
TheZ-Wave.me Z-Wave RaZberry Card 2 is a tiny daughter card designed for the Raspberry PI which allows it to function as a Z-Wave gateway.
Plugs into the Raspberry PI GPIO interface
Z-Wave Plus certified
Includes Z-Way AJAX-based demo user interface for easy access to Z-Wave functions
Includes all firmware drivers and Z-Wave stack
The optimized antenna provides greater range than the earlier model
Product Details
TheZ-Wave.me Z-Wave RaZberry Card 2adds all the components needed to turn a Raspberry PI board into a fully operational and inexpensive Z-Wave gateway. Designed to sit on top of the GPIO connector (not blocking the USB boards), it is powered by the Raspberry PI board with 3.3V and communicates using TTL signals (RX/TX).
Ithosts a Sigma Designs ZM5202 Z-Wave transceiver module, an external 32 K SPI flash for network data and a PCBA antenna. (Beside the PCBA antenna there is also an option to solder a whip antenna and an IPEX connector.)
Additionally, two LEDs are used to indicate the status of the Z-Wave controller chip.
TheZ-Wave.me Z-Wave RaZberry Card 2also contains Z-Wave low-level firmware that runs on the transceiver and Z-Way – the first certified Z-Wave communication stack which handles all Z-Wave network communication, a Javascript automation engine and a built-in web server. You can read more about theZ-Wave.me Z-Wave RaZberry Card 2's firmware on the z-wave.me website.
This device is intended for programmers who want to write their own user interface and applications however an Installer UI and Ajax web demo are available for download to get you started. You can find them on the z-wave.me website. A basic but functional mobile app is also available for Android and Apple devices.
This product is compatible with the following devices:
Raspberry PI 1 B
Raspberry PI 1 B+
Raspberry PI 2
Raspberry PI 3
The Raspberry PI is not included with this device.
Note:On the Raspberry Pi 3 you cannot use Bluetooth together with the Razberry Z-Wave module since both require a real hardware UART, but the Raspberry Pi 3 only has one UART.
Home Center 2 is an advanced whole-home management system which uses a web-based, feature rich graphics interface for simple programming. Control of your home is achieved through a wide range of native apps, voice control by Amazon Alexa or Google Assistant, or truly smart automation. The controller manages all FIBARO Z-wave devices as well as most 3rd party Z-wave devices with a wide library of built-in drivers for multimedia, which include smart TV’s, IP cameras, thermostats, security alarm systems, and media players. Home Center 2 also has its own alarm panel which allows you to arm/ disarm sensors individually, and even remotely. For larger homes or for multiple homes in different locations, Home Center 2 uniquely allows you to network several Home Centers (HC2 or HCL) into one system.
The Home Center 2 by Fibaro isn't just an electronic device. It's also a well-designed, innovative and user-friendly interface, featuring functions never seen before.
Your Home by FIBARO
FIBARO Home Center 2 is faster and more secure than most competitive solutions due to its built-in Intel 1.6 Atom processor which processes the software locally, stores your data on the controller itself. No cloud processing or data storage means your system will run even if the internet goes down while owning your data. Home Center 2 also has advanced user rights and management features coupled with independent GPS location allows for creative scenes based on individual family members, anywhere in the world.
The user-friendly interface is extremely easy to set up, navigate and manage on a smartphone or tablet. Additionally, the visual scene builder on the web interface is very intuitive, allowing even inexperienced users to build quick simple scenes. For more advanced scenes, installers can use LUA scripting to completely automate the system.
Data safety first
FIBARO knows what is the most important. The access to your home and your data are protected at the highest level - through the WAF and Anti-DDoS systems, encrypted communication using the TLS protocol and passwords using bcrypt.
Plug & Play
The FIBARO system is simple to install and use. The plug & play devices are ready for use immediately after unpacking and short configuration, the others are non-invasive during installation.
Voice control
The FIBARO is compatible with voice control technologies. Just tell the System what to do, and your wish will be fulfilled in seconds.
Remote access from anywhere
You can check the status of your devices as well as control your house from any place on Earth. As long as you’re connected to the Internet you can always see what’s going on in your house.
A home filled with peace
Among other things, FIBARO makes sure to care for your personal security, as well as instances of fire, flooding, burglary. It also helps the elderly, the children, and persons of limited mobility in their everyday life.
Save energy
FIBARO allows you to monitor the amount of electricity used by home devices. This way you can easily identify which pieces of hardware keep on bumping up your bills. You can also program the system to help you make the most of the savings.
The dreams have come true
Enjoy the convenience of living with the FIBARO. Treat yourself to an easier and more comfortable life with FIBARO. Discover having time for everything. Finally!
Exclusive Aluminium Casing
We have put a huge emphasis on styling and build quality so that Home Center 2 by Fibaro pleases You from the first time You look at it. What You see is what you get - Home Center 2 by Fibaro is made of solid aluminium. You won't find cheap plastic anywhere! Home Center 2 by Fibaro isn't just good-looking, true innovations hide inside.
Extremely Quick and Efficient Hardware Structure
Intel Atom 1,6Ghz Processor
Thanks to its efficiency, Home Center 2 is much, much faster than other Z-Wave gateways currently on the market. The communication within the Z-Wave network has improved dramatically, resulting in immediate response to commands sent by the home automation system user.
4GB MLC Recovery Disc
Significantly improved user safety thanks to Fibaro's proprietary approach to data protection. Each Home Center 2 has its own Recovery disc, holding system backups, unique to each gateway. This completely prevents unauthorised access to the system. Another advantage of this solution is quick and simple system recovery after any failure.
1GB RAM, 2GB SLC Hard Drive,
Large memory + fast processor = quick communication between Fibaro System devices. Hardware architecture used in the Home Center 2 makes Z-Wave based home automation system work much faster than ever before.
Quick and Easy Installation
Plug the power cord into the POWER connection and the network cable into the LAN port
Within 2 minutes of connecting to a power socket, the Home Center 2 is ready to operate. By default, your Home Center 2 waits to get an IP address from Your DHCP server. If unsure, hold RECOVERY button for a while when power on. By doing this Home Center 2 will automatically get the static IP 192.168.81.1 To access the control panel, type the Home Center 2 IP address in your web browser's address bar.
New Possibilities Thanks to Linked Devices
Your Home Cener 2 gives you new possibilities thaks to Linked Devices. The Linked Devices function lets you combine multiple devices into one virtual device with combined functionality - for example, 3 heater thermostats plus temperature and humidity sensors. The primary advantage of this feature is the convenience of being able to control multiple devices at the same time, at the press of one button. The second advantage is a reduction in the number of devices icons in the user interfaces.
Great Comfort Thanks to Device Panels
The Home Center 2 interface gives you easy control over groups of devices responsible for the same function - for example, heating, air conditioning or garden watering. Thanks to the Device Panels, you can easily schedule operations for groups of devices, based on the day of the week or the time of day.
Geo Localization
Your Home Center 2 gives you another unique functionality - Locating your family members. Now You can always know where your children are, without the need to call them every 5 minutes. Your Home Center 2 will get their location for You.
Your Home Center 2 shows Your family member route and current position on a map. TheHome Center 2 connects to mobile phones with the Fibaro Mobile Application installed to check their current position. TheFibaro Mobile Application determines a family members location and informs the Home Center 2 of it.
Advanced Scenes
Home Center 2 offers a new approach to scenes. Now scenes may be conditioned on any, user-defined variable.
Example Scene 1 "Rain"
If raining: - close roof windows, - turn garden sprinklers OFF, - set "it rained" variable to 1.
Example Scene 2 "Turn garden sprinklers on at 6:00 am"
Each day at 6:00 am check if "it rained" (user-defined variable). If not ("it rained" variable = 0) - turn the sprinklers ON.
Example Scene 3 "Reset variable"
If "it rained" and 12 hours passed from that time: - set "it rained" variable value to 0.
We have the honor to present you the new dimension of comfort – Home Center Lite, incredibly compact brain of the FIBARO System. Latest creation, designed with your needs in mind. Let it change your life, making it safer and more convenient, and your home intelligent, efficient and comfortable. Little thing – great effect!
Product Details
HC Lite is a tiny device with huge potential. Incredibly quick and effective. Control your home from anywhere in the World using a mobile phone or tablet. Begin creating your own world around delights and convenience provided by innovation.
LUA is a programming (scripting) language and is commonly used in home automation controllers to enable users to create more complex control scenes than supported by the controller's Scene editor. The HC2's scene editor enables you to use a graphical-based editor or a LUA-based editor, whereas the HCL only supports a graphical editor.
We feel this is the most important difference between the two controllers - and one that you need to think carefully about.
LUA Scenes
Almost all automation in the Fibaro System is controlled by 'Scenes'. For instance these can make lights turn on when motion is detected at particular times of the day or make several things happen from one simple button press of a remote control. Most of these scenes can be created in Fibaro controller's excellent 'Graphical Scene Editor'. But some more complex scenes are actually much easier to create using a LUA script, and in some extreme cases could only be created using LUA.
LUA is a very useful feature to have, occasionally, a simple LUA script can solve an issue that would have required a complex graphical scene.
Scene Controllers
Some remote controls that act as 'Scene Controllers' need a LUA-based scene to work correctly in the Fibaro Controllers.
Virtual Devices
Virtual devices are what they sound like - devices in the Fibaro controller that aren't linked to physical devices. Virtual devices are very useful for controlling devices via other networks, such as AV equipment that can be controlled from your Wi-Fi/Ethernet system (HTTP). They are also useful to create a simple button in the Fibaro App that can control a number of scenes - quickly and easily.
Scene and Device Control (LUA) To create Virtual devices that control scenes you need to use LUA, therefore, these types of Virtual Devices cannot be created in Home Center Lite.
Remote Control of 3rd Party Products (HTTP & IP) Virtual Devices can be created that control products via the IP network (Wi-Fi or Ethernet), via HTTP requests. These are fully supported in Home Center Lite as they use a different type of Virtual Device configuration and command protocol (HTTP Strings).
The DHS RGB LED Strip gives you the power to create stunning visual effects in your home allowing you to choose the atmosphere of your home with the use of light.
Unleash your fantasy decorating a living-room or bathroom. Create illumination effect to match weather conditions, your mood or a special occasion. 3 million colours on hand, waiting for your ideas!
This flexible strip light is perfect for any kind of illumination. Silicon gel type waterproof. It can be used for home ceiling, bathroom and kitchen lights, furniture, shelves and cupboards etc.
Product Details
All LED strip lights come standard with 3M adhesive backing which means they can be stuck pretty much anywhere giving you endless creative possibilities. You can use it as it is or together with the Fibaro Z-Wave RGBW Controller to create truly unique effects.
Fibaro Z-Wave RGBW Controller is a one of a kind, advanced wireless 4-colour LED strips controller. Apart from traditional RGB channels it also supports the additional white light channel which allows you to add pastel colours to your lighting decorations. The device may control up to four analogue sensors.
The Garage door limit switch is industrial quality switch operated by the motion of a garage door, gates ect. This switch can be connected with any binary Z-Wave sensors or Z-Wave door/window sensors to report status of garage door.
The Vision Z-Wave™ Siren and Strobe is a wireless device capable of producing an audible and visual alarm.
Blue LED flashing strobe light
Loud 105dB audible alarm
Low battery and Tamper indicators
Easy installation - no extra wires required
Includes a 15V DC power supply
Configurable with Z-Wave™ certified gateways
Product Details
The Vision Z-Wave™ Siren and Strobe (ZM1601AU) is a wireless device - programmable with certified Z-Wave™ gateways - capable of producing a loud audible and visual strobe alarm based on your Home Automation and/or Security Network settings.
This device is designed to operate alongside a Z-Wave™ enabled sensor which can detect a threat to your household.
The Vision Z-Wave™ Siren and Strobe also includes a battery status indicator which will notify you when its battery level is low. It also includes a tamper alarm, which sends an alarm signal to an associated Z-Wave™ gateway if anyone tries to tamper the device.
This product integrates with all Australian certified (921.42MHz) Z-Wave™ controllers including:
