vision

The RFXrtx433E USB transceiver enables you to control 433MHz-based devices from your computer or from a Z-Wave controller such as the Vera3 or Vera Lite. It supports a huge number of 433MHz-based products, including the LightwaveRF devices as well as Oregon Scientific, HomeEasy, Somfy...

The RFXrtx433E interfaces with a wide range of home automation software, including Domoticz, Homeseer, Indigo, Xtension, and hardware controllers such as the Vera3 and Vera Lite.

RFXtrx433E - Extended capabilities

This is the RFXtrx433E (Extended version) that replaces the previous RFXtrx433. It includes a hardware extension and additional firmware to enable it to support Somfy wireless blinds (RTS). The extedned functionality is already supported in Domoticzt, Homeseer and the VERA RFX plugin.

SPECS
Wireless Technology

• 433.92MHz

USB Interface

• USB 2.0

Power

• via USB

Dimensions

• 160 x 110 x 45 mm

The Vision 4 in 1Z-Wave Door/Window Sensor is a small, battery powered, magnetic sensor capable of detecting when a door/window is opened as well as changes in humidity, light and temperature.  This sensor is a Z-Wave enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave Plus enabled network and its security framework.  Vision 4 in 1Z-Wave D/W sensor sends Z-Wave signal when door or window is opened or closed or there is a humidity, temperature, luminance change.

The Vision 4 in 1Z-Wave D/W Sensor includes a smart magnetic door/window sensor consisting of two magnetic units, one is placed on the moving part of the door or window and the other on the frame. The sensor expands the capabilities of the system by monitoring the opening of doors, windows and garage doors.

When the sensor is triggered it can send binary ON/OFF commands wirelessly using a Z-Wave enabled (AUS/NZ version 921.42 MHz) transmitter to assigned controllers, switches, dimmers, blind controllers, fans, power boards, locks etc. The sensor can be used to automatically turn on lights, turn wireless switches ON/OFF and for security applications within the Z-Wave network as well as monitoring whether any doors or windows are open to ensure that your air-conditioning is not operating when it is not efficient to do so.

The Vision 4 in 1Z-Wave D/W Sensor also reports temperature , humidity and illumination changes to the associated Z-Wave gateway which can be used to improve the efficiency of your smart home.

Featuring the new Z-Wave 500 series chip the Vision 4 in 1Z-Wave D/W Sensor supports higher data transfer rates (9.6/40/100kbps) as well as over-the-air firmware updates meaning it is always operating with the most advanced firmware available.

Integrates with Australian Z-Wave certified (921.42MHz) controllers including:

• Fibaro Home Center 2
• Fibaro Home Center Lite
• Homeseer

The VISION Z-Wave Plus KeyFob (4) controller allows the user to wirelessly control home appliances using Z-Wave enabled devices.

The VISION Z-Wave KeyFob (4) is a fully functional Z-Wave remote controller capable of adding, removing and controlling other Z-Wave devices. Advanced functions include automatic rediscovery of the Z-Wave network as well the ability to become a secondary or inclusion controller to a SIS gateway in a Z-Wave network.

This product allows the user to control home appliances wirelessly using Z-Wave enabled (AUS/NZ version 921.42 MHz) devices like: switches, dimmers, blind controllers, fans, power boards, locks, ect.  An internal lithium battery allows for months of usage and can be recharged via USB.

The VISION Z-Wave Keyfob(4) offers four control buttons for scene selection.

 This product is compatible with:

Description

VISION Z-Wave Outdoor Siren

Vision Z-Wave Outdoor Siren & Strobe – Wireless Smart Home Security Alarm

Enhance your smart home security with the Vision Z-Wave Outdoor Siren and Strobe. This fully wireless Z-Wave Plus device is compatible with all major Z-Wave gateway controllers making it a seamless addition to your Z-Wave system. It features a powerful 115 dB siren and bright blue flashing strobe to alert you instantly to any security breach. Designed for easy DIY installation this outdoor siren is IP66-rated for weather resistance—ideal for tough Australian conditions. Battery-operated (4 x D batteries included) with an estimated 2-year battery life this outdoor Z-Wave alarm offers reliable long-term protection for your home or business.

Quick Overview

The VISION Z-Wave Siren and Strobe DC is a wireless device capable of producing an audible and visual alarm.

Product Details

Z-Wave Plus Outdoor Siren – Wireless Alarm with Visual & Audible Alerts

The Z-Wave Plus Outdoor Siren is a fully wireless programmable smart alarm designed to integrate seamlessly with any Z-Wave gateway. It delivers loud audible alerts and flashing visual warnings triggered by your Z-Wave network settings.

This outdoor siren is ideal for pairing with Z-Wave sensors to detect threats such as intrusion impact flooding or movement. Compatible devices include:

• DHS Z-Wave Multi-Sensor

• VISION Z-Wave Door/Window Multi-Sensor

• VISION Z-Wave Shock Sensor

• FIBARO Z-Wave Flood Sensor

• FIBARO Z-Wave Multi-Sensor

You can also pair it with the FIBARO Z-Wave Button to create an easily accessible panic alarm for home or office use.

Additional features include a low battery indicator and a tamper alert which notifies your Z-Wave controller if the device is disturbed or removed—ensuring added security and peace of mind.

This product integrates with all Australian-certified (921.42MHz) Z-Wave controllers including:

• Fibaro Home Center 3/Lite
• Homeseer HS3
• REMOTEC Z-Wave Universal Remote Controller
• RaZberry Pi
• Resolution security panels
• Alarm.com security panels

Note: This device includes DD batteries.

Product Support

Manuals:

⇒  Outdoor Z-Wave Siren Manual (Size: 260 kB)

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer importer distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Configuration Command Class:

Parameter 1: Siren/ Strobe Mode 1 Byte
Value: 0=Siren and Strobe enabled (default) 1=Siren only 2= Strobe only.
Parameter 2: Alarm auto stop time command 1Byte
Value: 0=30 seconds (default) 1= 60 secs 2= 120 secs 3= Siren will not stop automatically.

Federal Communications Commission Statement

This equipment has been followed to comply with Part 15 of the FCC Rules.
This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received including interference that may cause undesirable operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Technical Specifications

@20/44

 The Vision Z-Wave Range Extender is a smart, discrete Z-Wave device designed to amplify the signals of any Z-Wave devices in your Z-Wave network which helps to eliminate "RF dead spots".

• Designed to be concealed within a door/window frame
• Completely wireless
• Long battery life with low power alarm notification
• Tamper detection

SPECS
RF Protocol

• Z‐Wave Plus

RF Frequency

• 921.42Mhz ‐ AU/NZ approved RF for Z‐Wave

Z‐Wave Device Type

• Z-Wave binary sensor

Application

• Indoor use only

Colour

• White

Battery

• CR2 3V

Operation Temperature

• 0 ~ 50 °C

Dimensions

• (L x W x H) 65mm x 19mm x 19mm

Compliance

• RoHS 2011/65/EU, LVD 2006/95/EU, EMC 2004/108

 The VISION Z-Wave Shock Sensor is a smart, battery-powered sensor which detects any shocks and vibrations on the door or window which it is attached to.

Description

VISION Z-Wave Siren DC Powered

Quick Overview

The VISION Z-Wave Siren DC Powered is a wireless device capable of producing an audible and visual alarm.

The VISION Z-Wave Siren DC Powered is a wireless device fully programmable with Z-Wave gateways capable of producing an audible and visual alarm based on your Z-Wave network settings.

This device is designed to operate alongside a Z-Wave-enabled sensor which can detect a threat to your household. We recommend selecting any of the sensors below to suit your current needs:

Alternatively you can use it with the FIBARO Z-Wave Button as a convenient and easily accessible panic alarm in your home or office.

The VISION Z-Wave Siren and Strobe DC also includes a battery status indicator which will notify you when its battery level is low and a tamper alarm which will alert the associated Z-Wave gateway if anyone attempts to tamper with this device.

This product integrates with all Australian-certified (921.42MHz) Z-Wave controllers including:

• Vera Edge
• Vera Plus
• Fibaro Home Center 2/Lite
• Homeseer HS3
• REMOTEC Z-Wave Universal Remote Controller
• RaZberry Pi

Note: This device includes a 15V DC power supply.

Federal Communications Commission Statement

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Limited Warranty

Vision Guarantees that every wireless siren & strobe alarm is free from physical defects in material and workmanship under normal usage for one year from the date of purchase.

If the product proves defective during this one-year warranty period Vision will replace it free of charge. Vision does not issue any refunds. This warranty is extended to the original end user purchase only and is not transferable. This warranty does not apply to:
(1) damage to units caused by accident dropping or abuse in handling or any negligent usage;
(2) units which have been repaired taken apart or modified by an unauthorized personnel;
(3) units not used in accordance with instruction;
(4) damages exceeding the cost of the product;
(5) transit damage initial installation costs removal cost or reinstallation cost.

For information on additional devices please visit us at: www.visionsecurity.com.tw

Product Support

Manuals:

⇒ VISION Z-Wave Siren and Strobe User Manual (Size: 260 kB)

Configuration Command Class:

Parameter 0: Siren/ Strobe Mode 1 Byte
Value: 0=Siren and Strobe enabled (default) 1=Siren only 2= Strobe only.
Parameter 1: Alarm auto stop time command 1Byte
Value: 0=30 seconds (default) 1= 60 secs 2= 120 secs 3= Siren will not stop automatically.

Technical Specifications

@10/29

This Z-Wave USB dongle when attached to a PC, laptop etc, becomes a Z-Wave communication device, which connects the PC/MAC based Z-Wave software(sold separately) with different Z-Wave devices through integrated USB.

Within the Z-Wave wireless network the Z-Stick acts as a static controller with enhanced (SUC/SIS) network management function. In order to use the full functionality a software application such as Z-Cloud or Z-Way is needed to run on the host. Z-Stick supports all kinds of third party software complying with the Zensys Serial API.

• USB 2.0 full speed

• XP, Vista and Windows7

• Mac OS X 10.6.x Snow Leopard (and later)

• Range: 30m indoor

System Support

• Windows 7 (32 & 64 bit) or higher
• Linux kernel 2.6.24+
• MAC OSX6.4 or higher

Dimensions

• 28x88x10mm

The Vision Z-Wave™ Siren and Strobe is a wireless device capable of producing an audible and visual alarm.

• Blue LED flashing strobe light
• Loud 105dB audible alarm
• Low battery and Tamper indicators
• Easy installation - no extra wires required
• Includes a 15V DC power supply
• Configurable with Z-Wave™ certified gateways 

Product Details

The Vision Z-Wave™ Siren and Strobe (ZM1601AU) is a wireless device  - programmable with certified Z-Wave™ gateways  - capable of producing a loud audible and visual strobe alarm based on your Home Automation and/or Security Network settings.

This device is designed to operate alongside a Z-Wave™ enabled sensor which can detect a threat to your household.

The Vision Z-Wave™ Siren and Strobe also includes a battery status indicator which will notify you when its battery level is low. It also includes a tamper alarm, which sends an alarm signal to an associated Z-Wave™ gateway if anyone tries to tamper the device.

This product integrates with all Australian certified (921.42MHz) Z-Wave™ controllers including:

• Homeseer HS3
• Vera Edge
• Vera Plus
• Fibaro Home Center 2/Lite
• Homeseer HS3
• REMOTEC Z-Wave Universal Remote Controller
• RaZberry Pi

Product Support

Manuals:

⇒ VISION Z-Wave Siren and Strobe User Manual (Size: 260 kB)

Configuration Command Class:

Parameter 0: Siren/ Strobe Mode, 1 Byte
Value: 0=Siren and Strobe enabled (default), 1=Siren only, 2= Strobe only.
Parameter 1: Alarm auto stop time command, 1Byte
Value: 0=30 seconds (default), 1= 60 secs, 2= 120 secs, 3= Siren will not stop automatically.

Technical Specifications